The first thing you’ll need to do is install the rechargeable battery in the fan, as shown in the image above.
Then you’ll want to open up the battery compartment and unscrew the battery cap.
The cap should snap into the slot and hold the battery securely in place.
The battery itself is made of metal, which is easily removable.
The first step is to remove the plastic cover on the battery and remove the three screws holding the battery in place, as pictured below.
Then gently remove the battery cover from the fan by pulling on the back of the battery.
Then carefully remove the fan and remove it from the wall, as seen below.
You can also pop the battery back into place by gently tapping on the plastic plastic back plate.
The metal cover that holds the battery inside is fairly easy to remove, but it’s possible to remove and unscrub the battery with your fingers.
Next, you’ll remove the power cord.
You’ll need this piece to reconnect the battery to the fan.
If you don’t have one, you can buy one here.
Next you’ll have to remove a metal ring from the battery, as well as the connector.
The connector will come out on the top of the fan’s case, but you’ll be able to easily remove it by simply pushing it away.
Once you’ve done that, the power cable is now in the other side of the unit.
The fan is now ready to connect to the battery again, and you’ll likely have to unscrew and gently pull the battery out to connect it to the fans power supply.
You’re going to want to be careful with the power connector, though.
It’s a very thin piece and it can easily break.
The charging cable will also have to be removed.
It should come out of the base of the power supply, but we wouldn’t recommend trying to remove it at this point.
Next comes the connector that connects the battery power to the power source.
You will need to unscrow the baseplate of the connector to open it up and pull out the battery connector.
You won’t be able the pull out this connector, but the power is still connected.
If all else fails, you may need to use a screwdriver to loosen the battery plug.
You should now be able access the battery’s charging port, as you can see in the picture below.
Next come the two connectors that connect the fan to the back panel of the LED.
These two wires will go straight from the fans main power source, through the backpanel, into the battery adapter and into the fan itself.
You don’t need to connect them right now.
When you’re done reconnecting them, just unscrew one of the two wires that go to the adapter and pull it out.
You may have to loosen it slightly before you can plug it back in.
You could also try unscrewing the backplate and pulling it out, but again, you’d probably have to gently pull it back and plug it in.
The next connector you’ll use is the one that connects to the AC outlet.
The power cable connects from the AC power to your TV.
You might also want to connect a short length of wire to the outlets, as we did with the AC connector.
Once the cable has been disconnected, you should see the battery charging indicator light come on.
Now that you have the fan working, you need to remove its protective cover and connect it again.
If everything goes as planned, you’re now ready for your next rechargeable headlamp.
You also want the fan back in place so that you can connect it back to your house or car.
The LED’s power is only 12 watts and it only works with rechargeable batteries.
However, if you have an LED headlamps with a rechargeable rechargeable wall outlet, you will be able use the fan with these headlams.
To connect the LED back to the home, plug the battery into the wall outlet and plug in your other headlights, as previously described.
Finally, you must connect the AC adapter and power cord into the charging port.
This is where you’ll plug the charging cable back into the base.
Be sure to make sure that the charger’s power cord is in the right location, as this will be the connection to the wall.
You probably want to leave a little room around the charger, as the battery is still charging.
If things don’t work out, you might need to get a new rechargeable adapter to be able charge your new headlasts.
You shouldn’t need a new charger for this.
You still have two hours to complete this step, but if everything goes according to plan, you shouldn’t have to do any more work than that.